Every check valve does the same basic job: it lets flow through in one direction and stops it from going the other way. However, the check valve design that handles a 12-inch pump discharge application, may cause trouble on a raw sewage main, and vice-versa. Most comparison pages give you vague claims like "swing checks are bigger and stronger", with no dimensions, no weights, and no explanation of when each design actually wins. We've been selling check valves since 1965, so here's the comparison with real numbers included.
Swing Check Valves vs Wafer Check Valves: How Each Design Works
A swing check valve has a single disc (or door) on a hinge pin. Forward flow pushes the disc open and holds it against the top of the valve body. When flow stops, gravity swings the disc back onto the seat. The fully open disc sits clear of the flow path, which gives the swing check a full-port passage and low pressure loss, which is particularly suited to large bore, clean-service lines.
Before we get any further, let's clear up the naming convention. "Wafer check valve" covers at least three different valves on the market: single-disc wafer swing checks, dual-disc (dual-plate) wafer swing checks, and spring-loaded wafer silent checks. Each type behaves differently, and each fails differently. This article compares the full-body swing check valve against the dual-disc wafer check valve, which is what most buyers mean when they spec "wafer check valves".
A dual-disc wafer check valve uses two spring-loaded half-moon shaped discs mounted on a central hinge pin. Forward flow holds the discs open against a set of springs. As forward velocity decreases, the springs push the discs back toward the seat, so the valve is already closed before reverse flow fully develops. That closure time is related to hydraulic surge or "water hammer", which we'll discuss in more detail later.
Cracking pressure is an important parameter to compare. Titan's CV 41-DI dual-disc wafer opens at 0.25 psi. A swing check valve typically needs around 0.5 psi fully open; run it below that and the disc chatters on the seat, which wears the hinge pin and seat. If your system runs at low differential pressure for long stretches, the dual-plate valve is the safer option. Remember to always check the valve cracking pressure on the supplier data sheet before ordering.

Body Style, Face-to-Face Length, and Weight
A wafer check valve has no flanges of its own. The valve is clamped between two flanges on either side, and the flange through-bolts carry the joint. In comparison, a swing check valve may be purchased with integral cast flanges, allowing for separate flanged connections at both ends of the valve. Swing check valves are also available in threaded, welded and pressfit ends, especially for small bore valves.
The size and weight difference is larger than most engineers expect. A 12-inch Titan CV41 dual-disc wafer weighs 108 lb with a 5.62-inch inlet-to-outlet length. An equivalent Red White Valve 435 Series 12-inch flanged swing check is 27.5 inches long, and weighs 595 lb. That's more than five times heavier, and close to five times longer as well. The swing check valve might need a chainfall lift and pipe support under the valve, while the wafer check valve is installed with a come-along and two technicians. On skid layouts where every inch of run is fought over, the wafer body is often the difference between a design that fits and one that gets redrawn.
API 594 is the go-to standard for check valves, and it sets face-to-face dimensions for both swing and dual-plate wafer checks. That matters more than it sounds. When a valve dies ten years from now, an API 594 replacement from a different manufacturer drops into the same gap without cutting pipe.
Installation consumables follow the same pattern. The wafer reuses the mating-flange bolting you were already torquing, however longer through-bolts are needed. The swing check adds a second gasket and bolted connection.
Not sure if the wafer check meets your space and spec requirements? Talk to a ValveMan engineer, real engineers, not a call center; at 888-825-8800; before you start cutting any pipes.
Pressure Drop and Cv: Resolving Contradictory Claims
Articles and opinion pieces discussing this topic contradict each other. Some say that wafer valves restrict flow; others say that dual-plate designs have minimal head loss. Both are half-right, because each comparison uses a different baseline.
Here's our position after 60+ years of sizing and specifying these valves. A fully open, full-port swing check valves gives lower head loss for large, steady, clean lines, because the disc swings completely out of the stream and the bore is effectively an open pipe. A dual-disc valve keeps its plates in the flow path even when fully open, which means there's a flow restriction. The contoured body and streamlined discs keep the loss reasonable, and once you account for the length and weight you've saved, the dual-disc valve is competitive in most services. The "minimal head loss" claims are true when dual-plate check valves are compared against lift checks and silent checks. Against a full-port swing check valve of the same size, the swing check passes more flow.
Remember that most check valves have a minimum recommended velocity to ensure stable operation. Run the line too slowly and the door or discs flutter, resulting in grater head loss and increased wear on the hinge pin and springs. The general minimum recommended velocity for continuous stable operation is about 5 ft/s (1.5 m/s), although be sure to check the manufacturer information for your particular valve. Always size check valves for the actual flow conditions, and consider dropping a line size at the valve if needed to comply with velocity requirements.
Have a look at the Cv per size for each valve, and run the numbers yourself. The math is simple: pressure drop in psi equals (Q/Cv)² x SG (where SG represents specific gravity). For example, a valve with a published Cv of 1,000 passing 2,000 gpm of water loses (2,000 ÷ 1,000)² × 1.0 = 4 psi. Run that calculation for both candidate valves at your design flow, and the pressure drop might settle the debate for your installation.
Installation Orientation
Swing check valves typically handle both horizontal and vertical-up installation. A swing check installs with the hinge pin horizontal and above the pipe centerline, with vertical installation acceptable when the flow is upward, because gravity assists with valve closure in this configuration.
Dual-plate wafer check valves handle horizontal and vertical-up service too, with one nuance. In a vertical line, the weight of the plates adds to the spring force, so the effective cracking pressure rises, and the valve costs you slightly more head than the catalog figure taken in a horizontal run. In horizontal installations, hinge-pin and rib orientation matter; be sure to follow the manufacturer's IOM on which way the pin faces, rather than guessing from the casting.
Remember, vertical-down installation is not recommended for either design, unless specifically stated by the manufacturer.
For swing check valves, manufacturers usually call for 5 to 10 pipe diameters of straight run upstream of the valve. This helps to stabilize the flow and prevents turbulence which can cause the disc to chatter. For dual disc valves, typically 3 to 10 diameters of straight run is required. The most common field mistake we see is a check valve bolted directly to a pump discharge elbow. The swirl off the elbow keeps the disc dancing, the hinge pin wears out, and the valve gets blamed for a piping-layout decision.
Water Hammer and Valve Slam: Why Closure Speed Decides Pump Service

Consider what happens when a centrifugal pump trips. Forward flow decays, stalls, then reverses. A swing check valve disc has added mass and a long travel path, so reverse flow is already moving by the time the disc arrives at the seat. The slam you hear is the reversing column of fluid slamming the disc closed against the valve seat. The pressure spike from this hydraulic shock event may damage pipe fittings, crack gauges or blow gaskets.
The dual-disc wafer check valve's springs help to seat the valve discs while forward flow is still decaying, before the flow fully reverses. That difference is why dual-disc wafer checks are often found on centrifugal pump discharge service. For vertical discharge risers and tight HVAC mechanical rooms, a spring-loaded inline silent check valve does the same job with an even quicker response time, albeit at the cost of a more restricted flow path.
Process fluid considerations are equally important, because getting this wrong puts a valve in a line it can't survive. Standard dual-disc checks are intended for liquid service without suspended solids, and reciprocating-pump shock loads are not recommended. Solids get caught and stuck between the plates and the seat; while pulsating flow hammers the springs to death. Swing checks tolerate dirty service far better, since the full-port body passes rags, grit, and sludge that might wedge a dual-disc valve open.
The decision is simple. Centrifugal pump discharge on clean liquid favors a dual-plate wafer. Gravity sewer, raw water, and solids-bearing lines favor a swing check.
Standards and Pressure Classes That Matter at Purchase Time
Each standard on the spec sheet and nameplate answers a specific buying question. API 594 governs face-to-face dimensions, which protects your retrofit path. API 598 covers seat and shell testing, so a valve certified to API 598 should arrive with a documented leak test. API 6D applies to pipeline service. ASME B16.34 and B16.42 set pressure-temperature ratings for steel and ductile iron bodies, and AWWA C518 covers dual-disc check valves in waterworks service.
The pressure-class ladder comes with real numbers on the Titan line. The CV 41-DI ductile iron dual-disc wafer carries 250 psi WOG in Class 150 and 640 psi in Class 300 for 2 through 6-inch sizes. The CV46-CS carbon steel Class 600 series is rated 1480 psi WOG and references API 6D for pipeline work. Match the class to your system design pressure at temperature, using the B16.34 or B16.42 tables, and leave margin for transients.
Seat material follows the media and operating conditions. EPDM suits water and lower temperatures, Buna-N handles oils and fuels, Viton covers hydrocarbons at higher temperatures, and metal seats are the answer for steam and services beyond elastomer limits. Body material follows the class: ductile iron per B16.42 for water and HVAC, carbon steel for process lines and Class 600, stainless steel for corrosive media. If the job has sour-service requirements or needs material test reports, specify NACE compliance and MTRs when you order; they're cheap on the PO and expensive after delivery.
Matching class, body, and seat to your service pressure and media is exactly the call our team makes every day.
Selection Summary and Worked Example
Our selection order is this: pressure class first, then body material, then seat material, then spring and cracking pressure. Pick the series that satisfies the service conditions in that sequence. Engineers who start from a familiar model number and bend the service to fit it end up explaining a failed valve to someone.
Run two jobs through the framework. First, an 8-inch centrifugal pump discharge on clean water in a horizontal run: a Class 150 dual-disc wafer in the Titan Flow Control CV 41-DI style is the right call. The springs kill the slam, the design costs very little in head loss, the body fits between existing flanges, and two techs install it in an afternoon. Second, a 10-inch raw sewage force main: the dual-disc valve is disqualified outright by the solids limitation, so the job takes a swing check, ideally with an external lever and weight to speed closure. The full-port body passes the solids, and the lever gives the operator something to adjust when the line behaves badly.
Get the Spec Right the First Time
If you're not sure which valve is the best option for you, or if you have a challenging application like a reciprocating pump discharge, then send us your line size, media, flow rate, and design pressure. The ValveMan team in Exton, PA; real engineers, not a call center; will select, size and spec a valve against your actual service conditions.
Reach us through our contact page or call us directly at 888-825-8800. We've been sizing check valves against real service conditions since 1965, and a ten-minute conversation is much cheaper than a slamming valve.





